Model IMS1SE
The GlideLOCK adjustment will accommodate slots measuring 0.740' to 0.765' in actual width. The Miter Slider SE is not recommended for stationary jigs that must be locked into position within a miter slot. The standard aluminum Miter Slider is the best choice for these applications. Sold individually, order two for jigs that use both miter slots. If you're planning on making a sliding jig or fixture for your woodworking shop, the INCRA Miter Slider is exactly what you need. These inexpensive aluminum runners adjust for PERFECT sliding action in any standard (or near standard) 3/4' by 3/8' miter gauge slot with just a twist of the wrist.
Ships on December 18, 2020check in-store availability
The INCRA Miter Slider SE combines the versatility of the INCRA Build-It products with the unique performance and feel of the adjustable GlideLOCK miter bar used on INCRA miter gauges. Miter...
Compare With
Rip a 3 ⁄ 8 '-thick piece of hardwood, preferably hard maple, about 1 ⁄ 64' narrower than your saw’s miter slot. (Most are 3 ⁄ 4 ' wide.) Using a scrollsaw or bandsaw, cut three J-shaped kerfs as shown in the drawing, above, then drill a 1 ⁄ 8 ' hole in each 'tab,' making sure you don’t drill beyond the kerf. This rigid aluminum runner conveniently adjusts from the TOP for perfect sliding action in any standard 3/4' x 3/8' miter gauge slot. Won't warp, shrink, or swell like wooden runners. Adjustment range fits slots measuring 0.740' - 0.760' wide. A simple turn of a screw adjusts Miter Slider for ZERO sideplay. Mount these miter bars to the bottoms of your shop-made jigs and fixtures for a snug fit and a smooth glide. Each bar features three counterbored mounting holes, sized for 1/4' hardware. 516619 Miter Gauge Bar 19' Long with T-Slot Washer.
- Quick ViewModel IMS2$25.99
- Quick ViewModel IMS2SE$39.99
- Quick ViewModel IMS1$20.99
- Quick ViewModel MITERCHANNEL32$18.99
- Quick ViewModel ZP9-B1$15.99
- Quick ViewModel MITEREXPRESS$179.99
- Quick ViewModel BKITSTART$149.99
- Quick ViewModel MITER1000/SE$194.99
- Quick ViewModel ME/1000SEWC$324.99
- Quick ViewModel TTRACKREG18$10.99
Details
Best Miter Slot Runner Sled
The INCRA Miter Slider SE combines the versatility of the INCRA Build-It products with the unique performance and feel of the adjustable GlideLOCK miter bar used on INCRA miter gauges. Miter Slider SE is not recommended for stationary jigs that must be locked into position within a miter slot; choose standard aluminum Miter Slider for these applications. Steel bars are more rigid than wooden or plastic runners and are not susceptible to changes in humidity or temperature.
- This listing is for a single slider. Adjusts for slots 0.740' - 0.765'
- Miter Slider SE bars have (4) #10-24 holes that mate with INCRA Build-It Panels
- Miter Slider SE bars also have (3) 1/4'-20 holes along the length to accept knobs
- Fits square-sided 3/4' x 3/8' miter slots with or without T-slot bottom
- Miter Slider SE Bars are sold as single units
Reviews
Best Miter Slot Runner Saw
1 Review
Best Miter Slot Runner Parts
- 5.0 out of 5 stars
Incra Steel Miter Slider
I used the miter sliders to build a jig to cut pieces for segmented bowls.After adjusting them to my saws miter slots mounting them was easy if you follow the directions.When the jig was dialed in to the angle needed the sliders make the jig slide very easily.I like the fact that they are made of steel and the discs hold up very well to use.